Alliance Laundry Systems BF50PV Dokumentacja Strona 35
- Strona / 162
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Programming
33
F232059
Programming Tutorial
The following procedure guides the programmer
through a complete cycle and allows hands-on
experience for programming cycles. The complete
cycle is listed in Table 3.
1. Locate the key-operated programming switch
behind the access door directly below the
emergency stop button (top right on the front
panel of the washer-extractor).
Insert the key and turn the switch to PROGRAM
position. The display will read “CYC00”.
2. Press the Add Cycle key. The display will read
“ACYC00”.
3. A two-digit number from 01 to 39 must be
entered. Cycle number 39 is recommended
because standard program versions use this short
cycle for performing a chemical supply setup.
4. Press key 3, then key 9, then the Enter key. The
display will read “CYC39”.
a. If the display alternately flashes “EXISTS”
and “EDIT?”, press the Clear/Stop key. The
display will return to “CYC39”.
b. Erase the existing cycle: Press the Erase Cycle
key. The display will show “ECYC39”. Press
key 3, then key 9, then the Enter key. The
display will read “WA I T ” briefly and then
“CYC39”.
c. Press the Add Cycle key. The display will
read “ACYC39”. Press key 3, then key 9, then
the Enter key. The display will show “0139”.
5. Enter the desired function for step 1. A natural
choice might be hot fill to low level.
a. Press the Hot key and then the Low key. The
display will read “HL0139”.
b. Press the Enter key. The display will read
“M---S”.
c. Now enter the desired fill time. The
recommended number of minutes is four.
Press key 4. The display will read “4M-00S”.
6. Now press the Enter key. The display will read
“0239”, indicating that the computer is ready for
step 2 of cycle 39.
7. A natural choice for step 2 is the addition of a
supply.
a. To add supply No. 1, press the Supply key and
then key 1. The display will read “S10239”.
b. Press the Enter key and the display will read
“M---S”.
c. Now enter the desired time in minutes and
seconds for the supply valve to be turned on.
Thirty seconds is the recommended time.
Press key 0 for minutes, and the display will
read “0M-00S”.
Now press key 3 and then key 0. The display
will read “0M-30S”, indicating a supply time
of thirty seconds.
8. Now press the Enter key. The display will change
to read “0339”, indicating that the computer is
ready for step 3.
9. If no other supply is required, the next step is to
choose the type of wash desired and assign it a
time. For example, one might choose a wash with
standard reversing action (Wash 1) and a time of
six minutes.
a. Press the Wash key and then key 1. The
display will read “W10339”.
b. Press the Enter key. The display will read
“M---S”.
c. Press key 6. The display will read “6M-00S”,
indicating a wash step of six minutes.
10. Press the Enter key. The display will read“0439”,
indicating that the computer is ready for step 4.
11. A drain step usually comes next.
a. Press the Drain key. The display will read
“D-0439”. This program allows a choice
among drains 1, a, or b. For this application,
press key 1. The display will read “D10439”.
b. Then press the Enter key. The display will
read “M---S”.
c. Enter the maximum time desired for the
computer to allow the machine to drain to
empty. The recommended time is one minute.
Press key 1, and the display will change to
“1M-00S”, indicating a drain step of one
minute.
- Washer-Extractors 1
- Table of 3
- Contents 3
- Key to Symbols 6
- Operator Safety 7
- Safe Operating Environment 8
- Machine Location 9
- Input and Output Services 9
- AC Inverter Drive 10
- Operation 11
- Figure 1 12
- Figure 2 13
- Theory of Operation 14
- Wet Clean Capabilities 15
- WE-6 Microcomputer 17
- LED Display 17
- Operational Keypad 20
- Start-Up 22
- Opening Door 22
- Loading 22
- Supply Dispenser 23
- Cycle Selection 23
- Cycle Execution 23
- Test Cycle 24
- Stop Routine 25
- Balance Detection 26
- Temperature Display 27
- Figure 6 28
- WE-6 CONTROL BOARD 28
- Error Recovery Routine 29
- Thermal Overload Indicator 30
- Manual Mode Control Feature 31
- Programming 33
- Programming Tutorial 35
- Programming Hints 38
- System Programming 39
- Cycle Programming 41
- Editing a Cycle 42
- Erasing a Cycle in Memory 43
- Programming a Wet Clean Cycle 43
- Step Programming 44
- Programming Heat 49
- Programming a Wash Step 49
- Programming a Wash 5 Thermal 50
- Cool-Down 50
- Programming No Reversing 51
- Programming a Soak Step 51
- Programming a Drain Step 52
- Programming a Spin Step 52
- Programming an Auxiliary Step 52
- Transfer 54
- Figure 8 55
- Simulator 56
- Computer 57
- Preprogrammed Cycles 58
- Restaurants 59
- Shirt Laundries 59
- Standard Supply Legend 59
- Standard Cycle Charts 60
- Sample Cycle for Wet Clean 80
- Lavadoras 81
- Tabla de 83
- Seguridad 85
- Leyenda de los símbolos 86
- Entorno de operación seguro 88
- Uso indebido 90
- Figura 1 92
- Figura 2 93
- Teoría de operación 94
- Capacidades de limpieza por 95
- Pantalla de LED 97
- Microordenador WE-6 97
- Teclado de operación 100
- Output Indicators 101
- PRECAUCIÓN 102
- Distribuidor de suministro 103
- Tablas de ciclos 103
- Ejecución de los ciclos 103
- Ciclo de prueba 104
- ADVERTENCIA 105
- Detección del equilibrio 106
- Pantalla de temperatura 107
- Operación 108
- Figura 6 108
- TABLERO DE CONTROL WE-6 108
- Programación 113
- F232059 (SP) 114
- Programación del sistema 120
- Programación de un ciclo 122
- Modificación de un ciclo 123
- Programación de los pasos 125
- Modelos con 5 suministros 126
- Modelos con 8 suministros 127
- Programación de no inversión 132
- Programación de un paso de 133
- Operación del simulador y 135
- Figura 8 136
- Ciclos preprogramados 139
- Restaurantes 140
- Tablas de ciclos estándar 141
Powiązane produkty i podręczniki dla Pralki Alliance Laundry Systems BF50PV
Pralki Alliance Laundry Systems BF50PV Dokumentacja
(119 strony)
(119 strony)
(86 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 2.689 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji