Alliance Laundry Systems BF50PV Dokumentacja Strona 44
- Strona / 162
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Programming
F232059
42
Step Programming
Programming a Fill Temperature
Table 5 lists the required procedures to produce
specific results.
Table 5 shows that when HIGH water level is
programmed, the display indicator is “H”. When
MEDIUM level is programmed, the display indicator
is “M”. When LOW level is programmed, the display
indicator is “L”. When OVERFLOW is programmed,
the display indicator is “O”.
When the Warm key is pressed, the next key pressed
will be another temperature key (Hot, Cold, or Warm)
before selecting the level.
Use the following procedure to program a fill to a
specific temperature:
1. The computer must be in the Program Mode, and
the cycle programming sequence must be ready
for the next step.
2. Press the Cold key. If this is the second step of
hypothetical cycle 25, the display will read
“C-0225”. (HOT or WARM may be programmed
instead to control inlet valves during the first
three seconds of the fill. After the first three
seconds, the fill is the same regardless of the
prompt.) Press the key representing the desired
water level (Low, Medium, High, or Over). If
High is pressed, for example, the display will
read “CH0225”.
3. Press the Heat key. The display will read either
“080F25” or “025C25”, depending on whether
Fahrenheit or Centigrade is prompted.
Enter the desired fill temperature. Three digits
must be entered. If the desired temperature is less
than 100 degrees, the first digit must be 0. If
100 degrees Fahrenheit is entered, the display
will read “100F25”.
The valid temperature range is 80-200 degrees
Fahrenheit and 25-93 degrees Centigrade. The
computer will not accept temperatures out of this
range. (The fill temperatures possible are
governed by the temperature of the available hot
water.)
4. Press the Enter key. The display will read
“M---S”. Now assign the maximum time to be
allowed for reaching the fill level in minutes and
seconds.
5. Press the Enter key, and go to the next step in the
cycle.
The computer will attempt to maintain the temperature
within a margin of plus or minus five degrees of the
target fill temperature during such a step.
Table 5
Fill Temperature Programming
Keys Pressed Display Valves Operating
Hot + Low + Enter “HL” 1 Hot Fill
Hot + Med + Enter “HM” 1 Hot Fill
Hot + High + Enter “HH” 1 Hot Fill
Hot + Over + Enter “HO” 1 Hot Fill
Cold + Low + Enter “CL” 1 Cold Fill
Cold + Med + Enter “CM” 1 Cold Fill
Cold + High + Enter “CH” 1 Cold Fill
Cold + Over + Enter “CO” 1 Cold Fill
Warm + Low + Enter “WL” 1 Hot Fill and 1 Cold Fill
Warm + Med + Enter “WM” 1 Hot Fill and 1 Cold Fill
Warm + High + Enter “WH” 1 Hot Fill and 1 Cold Fill
Warm + Over + Enter “WO” 1 Hot Fill and 1 Cold Fill
In addition to the standard fill temperatures, computer-controlled fill or overflow to a specific temperature is available.
- Washer-Extractors 1
- Table of 3
- Contents 3
- Key to Symbols 6
- Operator Safety 7
- Safe Operating Environment 8
- Machine Location 9
- Input and Output Services 9
- AC Inverter Drive 10
- Operation 11
- Figure 1 12
- Figure 2 13
- Theory of Operation 14
- Wet Clean Capabilities 15
- WE-6 Microcomputer 17
- LED Display 17
- Operational Keypad 20
- Start-Up 22
- Opening Door 22
- Loading 22
- Supply Dispenser 23
- Cycle Selection 23
- Cycle Execution 23
- Test Cycle 24
- Stop Routine 25
- Balance Detection 26
- Temperature Display 27
- Figure 6 28
- WE-6 CONTROL BOARD 28
- Error Recovery Routine 29
- Thermal Overload Indicator 30
- Manual Mode Control Feature 31
- Programming 33
- Programming Tutorial 35
- Programming Hints 38
- System Programming 39
- Cycle Programming 41
- Editing a Cycle 42
- Erasing a Cycle in Memory 43
- Programming a Wet Clean Cycle 43
- Step Programming 44
- Programming Heat 49
- Programming a Wash Step 49
- Programming a Wash 5 Thermal 50
- Cool-Down 50
- Programming No Reversing 51
- Programming a Soak Step 51
- Programming a Drain Step 52
- Programming a Spin Step 52
- Programming an Auxiliary Step 52
- Transfer 54
- Figure 8 55
- Simulator 56
- Computer 57
- Preprogrammed Cycles 58
- Restaurants 59
- Shirt Laundries 59
- Standard Supply Legend 59
- Standard Cycle Charts 60
- Sample Cycle for Wet Clean 80
- Lavadoras 81
- Tabla de 83
- Seguridad 85
- Leyenda de los símbolos 86
- Entorno de operación seguro 88
- Uso indebido 90
- Figura 1 92
- Figura 2 93
- Teoría de operación 94
- Capacidades de limpieza por 95
- Pantalla de LED 97
- Microordenador WE-6 97
- Teclado de operación 100
- Output Indicators 101
- PRECAUCIÓN 102
- Distribuidor de suministro 103
- Tablas de ciclos 103
- Ejecución de los ciclos 103
- Ciclo de prueba 104
- ADVERTENCIA 105
- Detección del equilibrio 106
- Pantalla de temperatura 107
- Operación 108
- Figura 6 108
- TABLERO DE CONTROL WE-6 108
- Programación 113
- F232059 (SP) 114
- Programación del sistema 120
- Programación de un ciclo 122
- Modificación de un ciclo 123
- Programación de los pasos 125
- Modelos con 5 suministros 126
- Modelos con 8 suministros 127
- Programación de no inversión 132
- Programación de un paso de 133
- Operación del simulador y 135
- Figura 8 136
- Ciclos preprogramados 139
- Restaurantes 140
- Tablas de ciclos estándar 141
Powiązane produkty i podręczniki dla Pralki Alliance Laundry Systems BF50PV
Pralki Alliance Laundry Systems BF50PV Dokumentacja
(119 strony)
(119 strony)
(86 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 1.010 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji